RO Technology in Industrial Boiler Feedwater Systems

Created on 11.19
RO Technology in Industrial Boiler
Feedwater Systems
Boilers are the core pressure-bearing equipment of industrial thermal production, and feedwater quality directly affects the operating stability of the equipment, the efficiency of heat conversion and the service life of the whole unit. In accordance with two national industry standards - Water Quality for Industrial Boilers (GB/T 1576-2018) and Reverse Osmosis Water Treatment Equipment (GB/T 19249-2017) - make-up water for industrial boilers must have its core water quality indicators, such as hardness, conductivity, silica and dissolved oxygen, strictly controlled, so as to effectively avoid common equipment problems such as pipe scaling, internal corrosion and excessive heat loss. Boiler water treatment equipment has therefore become an indispensable supporting infrastructure of industrial thermal systems.
I. Core Process Principles and Quantitative Indicators of RO Water Treatment Equipment
RO water treatment equipment relies on the physical sieving and separation technology of high-polymer polyamide composite membranes. Under the normal operating pressure of 0.8-1.6 MPa, it precisely retains calcium and magnesium ions, colloids, suspended impurities, soluble salts and microorganisms in the water, allowing only water molecules to pass through the membrane elements to produce qualified purified water. Under the standard constant-temperature condition of 25 °C, the salt rejection rate of a single membrane element in compliant complete equipment is stably maintained at 98%-99.5%. The system water recovery rate is specified according to treatment capacity: small equipment below 4 m³/h has a recovery rate of not less than 30%, medium equipment of 4-40 m³/h has a recovery rate of not less than 50%, and large units above 40 m³/h have a recovery rate of not less than 70%. The long-term attenuation of the desalination rate can be controlled within 10%, fully meeting the requirements of the industry specification GB/T 16811-2018.
Matching water quality control standards can be selected according to the rated operating pressure of the boiler: low-pressure boilers (below 2.5 MPa) require a feedwater hardness of not more than 0.03 mmol/L; medium-pressure boilers (2.5-5.2 MPa) require a feedwater conductivity of not more than 5 μS/cm; high-pressure boilers (above 5.2 MPa) have even higher water quality requirements and need a polishing treatment unit to keep the outlet conductivity within 0.2 μS/cm. The permeate of conventional RO water treatment equipment can directly meet the water quality standards of low- and medium-pressure boilers, while two-stage RO combined with an EDI polishing module can meet the ultrapure make-up water demand of high-pressure boilers.
RO Boiler Water Treatment System for Industrial Boiler
II. System Design and Field Data of KONSMILE Environmental Protection Boiler Water Treatment Equipment
KONSMILE Environmental Protection customises complete sets of boiler water treatment equipment for different industrial boiler evaporation capacities and on-site raw water quality conditions. The whole system consists of a pretreatment unit, an RO main unit, an on-line water quality monitoring unit and an intelligent chemical dosing unit. The equipment architecture, component configuration and overall process design are all strictly benchmarked against the current national equipment manufacturing standards and energy efficiency control specifications, ensuring the compliance and stability of system operation.
In many large and medium-sized central heating projects in northern China, boiler operation has been significantly optimised after the system was upgraded with RO water treatment equipment. The annual scale deposit thickness on the boiler heating surfaces dropped from 1.2 mm before the retrofit to below 0.1 mm, and the overall thermal efficiency of the equipment increased by 6.3%. The boiler blowdown rate was reduced from 8%-10% with conventional softening processes to within 2.5%, and annual natural gas consumption can be reduced by 85,000 cubic metres, yielding quantifiable and traceable practical results in water and energy saving, cost reduction and efficiency improvement.
In terms of energy efficiency compliance, the RO system meets the national standard GB 37417-2019 (Minimum Allowable Values of Energy Efficiency for Reverse Osmosis Equipment), with the actual specific energy consumption for water production stabilised at 0.62-0.75 kWh/m³, better than the national limit value of 0.8 kWh/m³. The core membrane elements of the system have obtained NSF/ANSI 61 drinking water safety certification. The permeate has been fully verified by a third-party professional testing organisation, with key indicators such as heavy metals, total colony count and inorganic salt residues all conforming to industrial water and drinking water safety specifications, supported by complete compliance testing evidence.
III. Objective Advantages of Membrane-Based Boiler Water Treatment over Conventional Processes
Conventional sodium ion exchange softening equipment can only remove water hardness and cannot effectively reduce the total dissolved solids or silica content of the water. Such equipment requires frequent acid and alkali regeneration during long-term operation, easily generates high-salinity wastewater, and entails relatively high overall operating consumable costs and environmental disposal costs. Integrated boiler water treatment equipment equipped with RO units achieves desalination and purification through purely physical membrane separation, greatly reducing chemical usage frequency and wastewater discharge, in line with the current trend of water saving, consumption reduction and green, low-carbon development in industry.
Industry application statistics show that for boiler units using a full-membrane RO feedwater treatment system, the annual frequency of troubleshooting and maintenance is 37% lower than that of conventional ion exchange processes, effectively shortening equipment downtime for maintenance, reducing the indirect losses caused by production interruption, and improving the continuity and stability of industrial production.
Contact
Leave your information and we will contact you.

Customer services

Sell on waimao.163.com

Sherman
Sherman
Sherman
Janice